OVERVIEW
Member of the DimOnOff® building automation series, the REL-R-2.5 is a 2.5amp Powerline (Receive-only) module that provides remote control of fluorescent dimming ballasts, and daylight harvesting features when used in conjunction with a Lux sensor (INT-LUX).
The module features a small and compact design that allows to be installed inside a fluorescent ballast compartment.
The REL-R-2.5 is designed to be used in conjunction with one or more transceivers (e.g., CTL-KEY Keypad Controllers, INT-MIO sensor board, INT-LUX LuxMeter, etc.), or directly with the DimOnOff® Configuration, Control & Monitoring software.
With these different powerline modules, complex automation environments can be designed and operated.
FEATURES
- Designed to create flexible, smart automation systems for residential, commercial and industrial use
- Remotely control the DimOnOff® modules over the power lines, or over the Internet (Specify MOD-ETH, Powerline-Ethernet modem)
- Responds to On/Off or Bright/Dim/Setpoints commands, and many programmable Scenarios, Commands and Timers
- Designed to fit inside standard fluorescent fixture enclosures
- 100% Electronic output
- Equipped with leads and mounting bracket for easy installation
- Reliable powerline communication in high attenuation (0.5? min.) and noisy electrical environments
DimOnOff is a Compatible Control Partner for the Philips Mark 7 0-10V series of dimmable electronic ballasts
OVERVIEW
Member of the DimOnOff® building automation series, the REL-R-2.5 is a 2.5amp Powerline (Receive-only) module that provides remote control of fluorescent dimming ballasts, and daylight harvesting features when used in conjunction with a Lux sensor (INT-LUX).
The module features a small and compact design that allows to be installed inside a fluorescent ballast compartment.
The REL-R-2.5 is designed to be used in conjunction with one or more transceivers (e.g., CTL-KEY Keypad Controllers, INT-MIO sensor board, INT-LUX LuxMeter, etc.), or directly with the DimOnOff® Configuration, Control & Monitoring software.
With these different powerline modules, complex automation environments can be designed and operated.
FEATURES
- Designed to create flexible, smart automation systems for residential, commercial and industrial use
- Remotely control the DimOnOff® modules over the power lines, or over the Internet (Specify MOD-ETH, Powerline-Ethernet modem)
- Responds to On/Off or Bright/Dim/Setpoints commands, and many programmable Scenarios, Commands and Timers
- Designed to fit inside standard fluorescent fixture enclosures
- 100% Electronic output
- Equipped with leads and mounting bracket for easy installation
- Reliable powerline communication in high attenuation (0.5? min.) and noisy electrical environments
DimOnOff is a Compatible Control Partner for the Philips Mark 7 0-10V series of dimmable electronic ballasts
APPLICATIONS
- On/Off and Bright/Dim of 0-10V Fluorescent dimming ballasts
- Daylight harvesting and Load shedding
SPECIFICATIONS
- Operating voltage: 120 to 347-1VAC, 60Hz
- 262 kHz carrier frequency
- Load power rating: 2.5amp Ballast (electric discharge lamp)
- Can control up to four 0-10 V Dimming Ballasts
- Ambient operating temperature: -40°C to +40°C
Dimensions
Length: 4.875po - 123.82mm
Width: 2.125po - 53.175mm
Height: 1.5po - 38.1mm
CAUTIONS AND NOTES
The REL-R-2.5 must be installed inside fixtures or into an electrical box with proper size.
Only used for junction boxes where min. 90°C wiring is used.
These devices are intended for installation in accordance with your local electric code and regulations. It is recommended that a qualified electrician perform this installation.
A transmitter is required to communicate with the module and is sold separately. (Specify CTL-KEY Powerline keypad, or MOD-USB or MOD-ETH to be used with DimOnOff® Configuration, Control & Monitoring software
WIRING EXAMPLE
INSTALLATION INSTRUCTIONS
- Disconnect power at the circuit breaker before installation
- Open the fluorescent electrical compartment and identify the Line, Neutral and Ground wires. Identify the conductor that supplies power to the ballast that you want to control.
- Attach the REL-R-2.5 inside the electrical compartment using the module mounting bracket. Connect the supply Ground wire (G) together with the module mounting bracket and the grounding screw.
- Disconnect the Line wire that had supplied power to the lamp that you want to control.
- Connect the disconnected wire of the fixture to the Blue lead of the REL-R-2.5. Connect the supply Line wire (L) to the Black lead of the REL-R-2.5.
- Connect the white lead of the REL-R-2.5 together with the supply Neutral wire (N).
- Connect the purple wire to be Ballast 0-10 V input
- Place wires and module into the fixture.
- Close the compartment cover and restore power.
RELAYS
- REL-R-0.3 wireless PLC 300 Watts Relay
- REL-RT-5-MON Powerline 5 Amps Monitoring Relay
- REL-R-20 - MULTI-FUNCTION 20 AMP WIRELESS PLC RELAY
- REL-R-2.5 Load Module for Dimming Ballasts
- REL-RT-20 Powerline Relays 20 Amps
- REL-R-3x3 three outputs relay
- REL-XB-3X3 WIRELESS RF XB MESH 3 OUTPUTS RELAY
- REL-R-15 - Multi-function 15 amp wireless PLC Relay
- EO-PD - 300W Plug-in Dimmer / Relay
- EO-3WR - EnOcean Wireless 3-wire Relay Receiver
- Constant Voltage LED Dimmer
- REL-XB-10/20 Wireless RF mesh relay 10A (277-347) 20A (120-240)
- REL-XB-5-MON Wireless RF mesh relais with monitoring features
- EO-5WR - EnOcean Wireless 5-wire Relay Receiver
- ACC-CVLD Constant voltage LED dimmer
- ACC-CLK2 - Astronomical Clock
- EO-WSS10-GUZ - EnOcean RF Wall Switch Receivers Self-Powered
- INT-ADR-XB
2025 Lavoisier, suite 135, Québec City, Québec G1N 4L6, Canada